BVS 

BVS	Product Code: bvs Price: Check Latest Switch Mode DC Power supplies Universal Series:BVS * Single and Multiple outputs, 30 to 180 watts * Worldwide AC input range 90 to 264 VAC * Choice of tightly regulated, high peak current auxiliary outputs * Extremely versatile output configuration for a variety of applications * Superior light losd operation without audible noise * Power fail/logic inhibit signal on 80W * DC "OK" and remote sense signal on 180W units * UL, CSA, recognized and CE marked * 4-hour burn-in * 2-year warranty
General Specifications          Datasheet PDF AC Input: BVS products automatically adjust to the input voltage as follows: BVS30, 40, 60 and 80: wide range input from 90-264 VAC DC Outputs: See Voltage/Current Rating Charts.(Standard Models) Output Power: See Voltage/Current Rating Charts.(Standard Models) Peak Output Power: See Voltage/Current Rating Charts.(Standard Models) Sixty second maximum peak power duration’s. A 10% duty cycle is not to be exceeded when peak power duration’s are combined. Brown-Out Voltage: Regulation is maintained with full rated load at 90 VAC Hold-Up Time: 20 msec typical at full rated load and nominal AC input voltage. Hold-up time increases to 40 msec at 50% load. Power-Fail Warning Signal: TTL compatible signal goes low before the main +5V output drops 5%, at full rated load on BVS 80 Typical warning time:       BVS 80:       5 msec where applicable Warning time increases at reduced load levels Efficiency: Measured at full rated load and nominal AC input voltage. 75% ±5% depending on how the load is distributed among the outputs. Regulation Characteristics: See Voltage/Current Rating Charts for individual model ratings. Measurement method: Line: Measured over a 90-132 VAC or 175-264 VAC line change. Load: Measured over a 20% to 100% load change. Multiple output model regulation is subject to the minimum load           requirements mentioned below. Minimum Loads: The following minimum loads are required to maintain regulation. Multiple output models are expressed as current on the main output. Multiple output Single output   Multiple Output Single Output BVS 80 1A 5 Watts BVS 40, 60 0.5A 3 Watts BVS40 board only models: Consult factory for minimum load requirements. Please note those minimum load requirements increase at temperatures over 50°C. Initial Setting Tolerance: Measured at 50% of full rated load on all outputs. Remote Sensing: Optional on selected models only. Output Noise and Ripple: 0.3% RMS, 1% PK-PK maximum on main +5V output. Transient Response: Main +5V output: 500 sec typical for a 50-100% load change and recovery to within 1% of initial voltage set point. Maximum excursion: 4% from initial voltage set point. Overload Protection: Fully protected against output overload and short circuit. Automatic recovery upon removal of overload condition. Delayed-foldback current limiting characteristics assure reliable turn-on into reactive and non-linear loads. Overvoltage Protection: Provided on the main +5V output. Factory set at 6.2V±0.6V. Power-Up Initialization Period: Typical 2.0 sec turn-on delay assures orderly ramp-up and stabilization of all output voltages during power-up. Input Protection: AC input line fuse provided. Internally located. Inrush Current: Internally limited by thermistor. Temperature Rating: Operating: 0°C to +50°C at full rated output power. Derate linearly to 50% of full load from 50°C to 70°C. Storage: -55°C to +85°C. Temperature Coefficient: ±0.03%/°C typical, ±0.05%/°C maximum over entire operating temperature range of 0°C to +70°C. Cooling: Convection cooling is adequate for convection power ratings providing that non-restricted convection air movement is available. When operating in a confined area, forced air cooling is recommended. See voltage/current rating charts for individual model airflow requirements. Vibration: Random vibration from 10Hz to 2KHz, 6.15 grms (3 axis). Shock: Operating: 20G peak acceleration. Safety Agency Certifications: UL 1950 without D3 deviation, file #E181899 CSA C22.2 No. 950, UL file #E181899 CE Marked Standard Models SINGLE OUTPUT MODELS, selection guide      Datasheet PDF Forced air ratings are specified with 200 LFM of air movement. Normal Voltage Model Convection Cooled Current Forced Air Current Initial Setting Tolerance Line Regulation Load Regulation Output Adjustmemt Range Configuration 5V BVS-030 S10052 6A/8Apk N/A 5.0V±.2% 0.2% 3% 4.75V to 5.50V BOARD ONLY 5.00" x 3.00" x 1.17" (127mm) x (76.2mm) x (29.7mm) BVS-040 S10051 8A/11Apk N/A 5.1V±.2% 0.2% 1% 4.75V to 5.50V U-Channel Chassis 6.00" x 3.27" x 1.60" (152.4mm)x(83.06mm) x (40.64mm) BVS-040 S10052 8A/11Apk 11A 5.0V±.2% 0.2% 1% 4.75V to 5.50V BOARD ONLY 5.00" x 3.00" x 1.38" (127mm)x(76.2mm) x (35.1mm) BVS-080 S10051 16A/18Apk N/A 5.1V±.2% 0.2% 1% 4.75V to 5.50V U-Channel Chassis 7.20" x 4.20" x 1.80" (182.88mm) x (106.68mm)x(45.72mm) 12V-15V Adjustable* BVS-040 S10122 3.4A 2.2A 4.6A 3A 12.0V±.2% 0.2% 1% 11V to 18V BOARD ONLY 5.00" x 3.00" x 1.38" (127mm)x(76.2mm) x (35.1mm) BVS-060 S10121 5A/5.8Apk 4A/4.7Apk N/A 12.1V±.1% 0.2% 2% 11V to 16V U-Channel Chassis 6.00" x 3.27" x 1.60" (152.4mm)x(83.06mm) x (40.64mm) BVS-080 S10121 7.5A/9.2Apk 6A/7.3Apk N/A 12.1V±.1% 0.2% 1% 11V to 16V U-Channel Chassis 7.20" x 4.20" x 1.80" (182.88mm) x (106.68mm)x(45.72mm) 24V-28V Adjustable* BVS-040 S10242 1.7A 1.4A 2.3A 1.9A 24.0V±.2% 0.2% 1% 23V to 29V BOARD ONLY 5.00" x 3.00" x 1.38" (127mm)x(76.2mm) x (35.1mm) BVS-060 S10241 2.5A/3Apk 2.2A/2.5Apk N/A 24.0V±.2% 0.2% .5% 23.5V to 29V U-Channel Chassis 6.00" x 3.27" x 1.60" (152.4mm)x(83.06mm) x (40.64mm) BVS-080 S10241 3.8A/4.6Apk 3.2A/3.9Apk N/A 24.0V±.2% 0.2% .5% 23V to 29V U-Channel Chassis 7.20" x 4.20" x 1.80" (182.88mm)x (106.68mm)x(45.72mm) * 12V Adjustable models have currents expressed as 12V/15V operation. 24V adjustable models have currents expressed as 24V/28V operation. NOTE A: Voltage level adjustable from 4.75V to 5.50V. MULTIPLE OUTPUT MODELS, selection guide      Multiple Output Models(1p) Multiple Output Models(2p) Multiple Output Models(3p) Power ratings are convection cooled unless otherwise noted. Power(Watts) Model Voltage Current Initial Setting Tolerance Line Regulation Load Regulation Configuration Continuous Peak 50 55 BVS-050 M20012 +12V 2.1A/2.3A PK Adjustable 10.8 to 13.2V 0.2% 2% BOARD ONLY 7.00" x 2.00" x 1.25" (177.8mm) x (50.8mm) x (31.8mm) -12V 2.1A/2.3A PK ±4% Note C 0.5% 2% 55 65 BVS-060 M40001 +5V 6A Adjustable Note A 0.2% 2% U-Channel Chassis 6.00" x 3.27" x 1.60" (152.4mm)x (83.06mm)x(40.64mm) +12V 3A/4A PK ±4% Note C 0.2% 2% -5V 0.5A Note F ±4% Note C 0.5% 2% -12V 0.5A Note F ±4% Note C 0.5% 2% 55 65 BVS-060 M40011 +5V 6A Adjustable Note A 0.2% 2% U-Channel Chassis 6.00" x 3.27" x 1.60" (152.4mm)x (83.06mm)x(40.64mm) +24V 1.5A/2.5A PK ±4% Note C 0.2% 2% -12V 0.5A Note F ±4% Note C 0.5% 2% +12V 0.5A Note F ±4% Note C 0.5% 2% 55 65 BVS-060 M40021 +5V 6A Adjustable Note A 0.2% 2% U-Channel Chassis 6.00" x 3.27" x 1.60" (152.4mm)x (83.06mm)x(40.64mm) +12V 3A/4A PK ±4% Note C 0.2% 2% -12V 0.5A Note F ±4% Note C 0.5% 2% +12V 0.5A Note F ±4% Note C 0.5% 2% 55 65 BVS-060 M40021 +5V 6A Adjustable Note A 0.2% 2% U-Channel Chassis 6.00" x 3.27" x 1.60" (152.4mm)x (83.06mm)x(40.64mm) +15V 2.5A/3.5A PK ±4% Note C 0.2% 2% -5V 0.5A Note F ±4% Note C 0.5% 2% -15V 0.5A Note F ±4% Note C 0.5% 2% 55 65 BVS-060 M40041 +5V 6A Adjustable Note A 0.2% 2% U-Channel Chassis 6.00" x 3.27" x 1.60" (152.4mm)x (83.06mm)x(40.64mm) +24V 1.5A/2.5A PK ±4% Note C 0.2% 2% -15V 0.5A Note F ±4% Note C 0.5% 2% +15V 0.5A Note F ±4% Note C 0.5% 2% 80 90 BVS-080 M40001 +5V 14A Adjustable Note A 0.2% 1% U-Channel Chassis 7.20" x 4.20" x 1.80" (182.88mm)x (106.68mm)x(45.72mm) +12V 4A/7A PK Adjustable Note B 0.2% 1% -5V 1A ±4% Note C 0.5% 2% +12V 1A ±4% Note C 0.5% 2% 80 90 BVS-080 M40011 +5V 14A Adjustable Note A 0.2% 1% U-Channel Chassis 7.20" x 4.20" x 1.80" (182.88mm)x (106.68mm)x(45.72mm) +24V 2A/3.5A PK Adjustable Note B 0.2% 1% -12V 1A ±4% Note C 0.5% 2% +12V 1A ±4% Note C 0.5% 2% 80 90 BVS-080 M40021 +5V 14A Adjustable Note A 0.2% 1% U-Channel Chassis 7.20" x 4.20" x 1.80" (182.88mm)x (106.68mm)x(45.72mm) +12V 4A/7A PK Adjustable Note B 0.2% 1% -12V 1A ±4% Note C 0.5% 2% +12V 1A ±4% Note C 0.5% 2% 80 90 BVS-080 M40031 +5V 14A Adjustable Note A 0.2% 1% U-Channel Chassis 7.20" x 4.20" x 1.80" (182.88mm)x (106.68mm)x(45.72mm) +15V 3.5A/6A PK Adjustable Note B 0.2% 1% -5V 1A ±4% Note C 0.5% 2% -15V 1A ±4% Note C 0.5% 2% 80 90 BVS-080 M40041 +5V 14A Adjustable Note A 0.2% 1% U-Channel Chassis 7.20" x 4.20" x 1.80" (182.88mm)x (106.68mm)x(45.72mm) +24V 2A/3.5A PK Adjustable Note B 0.2% 1% -15V 1A ±4% Note C 0.5% 2% +15V 1A ±4% Note C 0.5% 2% 80 90 BVS-080 M41001 +5V 14A Adjustable Note A 0.2% 1% U-Channel Chassis 7.20" x 4.20" x 1.80" (182.88mm)x (106.68mm)x(45.72mm) +12V 4A/7A PK Adjustable Note B 0.2% 1% -5V 1A ±4% Note C 0.5% 2% -12V 3A ±4% Note C 0.5% 2% 80 90 BVS-080 M42001 +5V 14A Adjustable Note A 0.2% 1% U-Channel Chassis 7.20" x 4.20" x 1.80" (182.88mm)x (106.68mm)x(45.72mm) +12V 4A/7A PK Adjustable Note B 0.2% 1% -12V 1A ±4% Note C 0.5% 2% -5V 3A ±4% Note C 0.5% 2% 100 113 BVS-100 EG03 +6.5V 9.6A/10A PK Adjustable 6.2V to 6.8V 0.2% 1% BOARD ONLY 9.00" x 2.20" x 1.55" (228.6mm)x(55.8mm) x(39.4mm) +12V 1.6A/2A PK ±4% Note C 0.5% 2% -12V 1.6A/2A PK ±4% Note C 0.5% 2% 180 180 BVS-180 M20011 +5V 12A Adjustable Note A 0.2% 1% U-Channel Chassis 5.50" x 5.00" x 1.65" (139.7mm)x(127.0mm) x(41.9mm) +12V 10A Adjustable Note B 0.2% 1% Notes: A. Voltage level adjustable from 4.75V to 5.50V. B. Full regulated output, voltage adjustable ±4% minimum. Factory set to ±1% of nominal. C. Fully regulated output, voltage fixed. D. Voltage level adjustable from 10V to 16V. Factory set to 12V ±0.2V. E. Quasi regulated output. See regulation curves at the end of this section. F. Max load on V3 or V4 can be 1 amp if either V3 or V4 is unloaded. Dimensions Datasheet PDF      Datasheet PDF